GAMEROMS-SCAMMER
New Member
**** OLD OLD OLD OLD *****
THESE ARE DIAGRAMS OF THE ***OLD*** VIKING CHIP FROM BACK WHEN... KEPT HERE FOR POSTERITY ONLY. FIND THE STICKIED THREADS OR HIT THE DOWNLOADS PAGE ON THE WEBSITE FOR CURRENT INSTALL INSTRUCTIONS********
VIKING360 is not responsible for any risk, liability or damage, legal or otherwise, to you, your property, yourself, or anything! You assume all risks, responsibilities and liabilities!
Im gonna label all the easy points on the front and the back of the CG PCB and you can decide where you want to wire, only 1 wire per color is needed so dont wire to the front and back of controller pcb. choose the best location for you to install each wire.
The reason for the colors with the black dots is i have 10 colors of kynar and to make install easier for me i will take a black sharpie and mark a line down the wires to make it easier to identify dupe colors.
VIKING 360 DUO DIAGRAMS
PIN HEADER
IF YOUR PIN HEADER HAS 4 OR 6 PINS MAKE SURE YOU REMOVE THE ONES NOT NEEDED, I'VE MARKED THEM IN THE PIC BELOW.
FRONT
BACK
NOTE: THE WIRES FOR THE A BUTTON AND RIGHT THUMBSTICK CAN ONLY BE INSTALLED ON THE BACK OF THE CHIP.
DUO CG TOP (TACT SWITCGES ARE ONLY LABELED IN THE CG TOP DIAGRAM)
DUO CG BOTTOM
DRILLING HOLE FOR USB PROGRAMER
THIS ONE IS HARD TO EXPLAIN CAUSE YOU WANT TO LINE IT UP CORRECTLY AND ITS KINDA HARD TO LINE UP AND MARK WITH THE PIN HEADER, SO I MADE ME A CARDBOARD CLONE THAT WORKED PERFECT. I TOOK A SMALL DRILL BIT AND DRILLED A HOLE IN THE CENTER OF EACH OF THE BLACK DOTS ON THE CARDBOARD, THEN LINED IT UP PROPERLY AND PUSHED A SMALL LATCH PIN THROUGH THE HOLE TO MARK THE DRILL SPOT. I USED 5/32 FOR PILOT HOLE AND 17/64 FOR THE FINAL HOLE.
DRILLING HOLE FOR TACT SWITCHES
WARNING: IF YOU USE A CHAT PAD WHEN YOU GAME DONT USE THIS SPOT, I USE IT BECAUSE I HAVE BIG HANDS AND MY FINGER LINES UP PERFECT.
YOU CAN USE ANY LOCATION YOU WANT TO INSTALL THE TACT SWITCHES, HERE IS A EXAMPLE OF THE LOCATION I USED. I USED A SMALL BIT TO DRILL THE PIOLT HOLE AND THEN A 5/32 BIT.
TACT SWITCH MOUNTING & WIRING
WIRING FOR THE A BUTTON AND R. THUMBSTICK ON BACK OF VIKING360
DUO CG TOP WIRED
DUO CG BOTTOM WIRED
NOTE: THE 6 WIRES ON THE RIGHT SIDE ARE IN THE ORIGINAL KEEP OUT AREA, BUT IF YOU RUN THE WIRES PROPERLY AND CHECK THERE PLACEMENT WITH THE BOTTOM OF THE CONTROLLER SHELL THERE WILL BE NO ISSUES.
MY SPIDER WEB
16 WIRES + 2 GND WIRES FOR TACT SWITCHES MAKES IT TOUGH TO KEEP IT LOOKING GOOD WITH THE LIMITED SPACE YOU HAVE. I INSTALLED IT AND #4 LED WAS BLINKING SO I REMOVED EVERYTHING AND REINSTALLED. ILL TRY TO REPLACE WITH A BETTER PIC FROM NEXT INSTALL
FINISHED PRODUCT
THESE ARE DIAGRAMS OF THE ***OLD*** VIKING CHIP FROM BACK WHEN... KEPT HERE FOR POSTERITY ONLY. FIND THE STICKIED THREADS OR HIT THE DOWNLOADS PAGE ON THE WEBSITE FOR CURRENT INSTALL INSTRUCTIONS********
VIKING360 is not responsible for any risk, liability or damage, legal or otherwise, to you, your property, yourself, or anything! You assume all risks, responsibilities and liabilities!
Im gonna label all the easy points on the front and the back of the CG PCB and you can decide where you want to wire, only 1 wire per color is needed so dont wire to the front and back of controller pcb. choose the best location for you to install each wire.
The reason for the colors with the black dots is i have 10 colors of kynar and to make install easier for me i will take a black sharpie and mark a line down the wires to make it easier to identify dupe colors.
VIKING 360 DUO DIAGRAMS
PIN HEADER
IF YOUR PIN HEADER HAS 4 OR 6 PINS MAKE SURE YOU REMOVE THE ONES NOT NEEDED, I'VE MARKED THEM IN THE PIC BELOW.
FRONT
BACK
NOTE: THE WIRES FOR THE A BUTTON AND RIGHT THUMBSTICK CAN ONLY BE INSTALLED ON THE BACK OF THE CHIP.
DUO CG TOP (TACT SWITCGES ARE ONLY LABELED IN THE CG TOP DIAGRAM)
DUO CG BOTTOM
DRILLING HOLE FOR USB PROGRAMER
THIS ONE IS HARD TO EXPLAIN CAUSE YOU WANT TO LINE IT UP CORRECTLY AND ITS KINDA HARD TO LINE UP AND MARK WITH THE PIN HEADER, SO I MADE ME A CARDBOARD CLONE THAT WORKED PERFECT. I TOOK A SMALL DRILL BIT AND DRILLED A HOLE IN THE CENTER OF EACH OF THE BLACK DOTS ON THE CARDBOARD, THEN LINED IT UP PROPERLY AND PUSHED A SMALL LATCH PIN THROUGH THE HOLE TO MARK THE DRILL SPOT. I USED 5/32 FOR PILOT HOLE AND 17/64 FOR THE FINAL HOLE.
DRILLING HOLE FOR TACT SWITCHES
WARNING: IF YOU USE A CHAT PAD WHEN YOU GAME DONT USE THIS SPOT, I USE IT BECAUSE I HAVE BIG HANDS AND MY FINGER LINES UP PERFECT.
YOU CAN USE ANY LOCATION YOU WANT TO INSTALL THE TACT SWITCHES, HERE IS A EXAMPLE OF THE LOCATION I USED. I USED A SMALL BIT TO DRILL THE PIOLT HOLE AND THEN A 5/32 BIT.
TACT SWITCH MOUNTING & WIRING
WIRING FOR THE A BUTTON AND R. THUMBSTICK ON BACK OF VIKING360
DUO CG TOP WIRED
DUO CG BOTTOM WIRED
NOTE: THE 6 WIRES ON THE RIGHT SIDE ARE IN THE ORIGINAL KEEP OUT AREA, BUT IF YOU RUN THE WIRES PROPERLY AND CHECK THERE PLACEMENT WITH THE BOTTOM OF THE CONTROLLER SHELL THERE WILL BE NO ISSUES.
MY SPIDER WEB
16 WIRES + 2 GND WIRES FOR TACT SWITCHES MAKES IT TOUGH TO KEEP IT LOOKING GOOD WITH THE LIMITED SPACE YOU HAVE. I INSTALLED IT AND #4 LED WAS BLINKING SO I REMOVED EVERYTHING AND REINSTALLED. ILL TRY TO REPLACE WITH A BETTER PIC FROM NEXT INSTALL
FINISHED PRODUCT