GAMEROMS-SCAMMER
New Member
**** OLD OLD OLD OLD *****
THESE ARE DIAGRAMS OF THE ***OLD*** VIKING CHIP FROM BACK WHEN... KEPT HERE FOR POSTERITY ONLY. FIND THE STICKIED THREADS OR HIT THE DOWNLOADS PAGE ON THE WEBSITE FOR CURRENT INSTALL INSTRUCTIONS********
VIKING360 is not responsible for any risk, liability or damage, legal or otherwise, to you, your property, yourself, or anything! You assume all risks, responsibilities and liabilities!
UPDATE 7/14: SLEEPER TUTORIAL SHOULD BE COMPLETE SOON AS I RECEIVE THE CHIPS FROM VIKING THAT WERE SHIPPED TODAY. THE DUO INSTALL WILL BE COMPLETE TODAY AND I DONT WANT REMOVE THE CHIP FROM THE DUO TO COMPLETE THE SLEEPER., CHIPS SHOULD ARRIVE BY FRIDAY ..
Im gonna label all the easy points on the front and the back of the CG PCB and you can decide where you want to wire, only 1 wire per color is needed so dont wire to the front and back of controller pcb. choose the best location for you to install each wire.
The reason for the colors with the black dots is i have 10 colors of kynar and to make install easier for me i will take a black sharpie and mark a line down the wires to make it easier to identify dupe colors.
VIKING 360 SLEEPER DIAGRAMS
PIN HEADER
IF YOUR PIN HEADER HAS 4 OR 6 PINS MAKE SURE YOU REMOVE THE ONES NOT NEEDED, I'VE MARKED THEM IN THE PIC BELOW.
NOTE: THE WIRE FOR THE A BUTTON CAN ONLY BE INSTALLED ON EITHER OF THE 2 GREEN POINTS ON THE BACK OF THE CHIP.
FRONT
BACK
NOTE: THE WIRE FOR THE A BUTTON CAN ONLY BE INSTALLED ON EITHER OF THE 2 GREEN POINTS ON THE BACK OF THE CHIP.
SLEEPER CG TOP
SLEEPER CG BOTTOM
(ONLY 7 EASY TO SOLDER POINTS ON THE BOTTOM)
DRILLING HOLE FOR USB PROGRAMER
THIS ONE IS HARD TO EXPLAIN CAUSE YOU WANT TO LINE IT UP CORRECTLY AND ITS KINDA HARD TO LINE UP AND MARK WITH THE PIN HEADER, SO I MADE ME A CARDBOARD CLONE THAT WORKED PERFECT. I TOOK A SMALL DRILL BIT AND DRILLED A HOLE IN THE CENTER OF EACH OF THE BLACK DOTS ON THE CARDBOARD, THEN LINED IT UP PROPERLY AND PUSHED A SMALL LATCH PIN THROUGH THE HOLE TO MARK THE DRILL SPOT. USED 5/32 FOR PILOT HOLE AND 17/64 FOR THE FINAL HOLE.
THESE ARE DIAGRAMS OF THE ***OLD*** VIKING CHIP FROM BACK WHEN... KEPT HERE FOR POSTERITY ONLY. FIND THE STICKIED THREADS OR HIT THE DOWNLOADS PAGE ON THE WEBSITE FOR CURRENT INSTALL INSTRUCTIONS********
VIKING360 is not responsible for any risk, liability or damage, legal or otherwise, to you, your property, yourself, or anything! You assume all risks, responsibilities and liabilities!
UPDATE 7/14: SLEEPER TUTORIAL SHOULD BE COMPLETE SOON AS I RECEIVE THE CHIPS FROM VIKING THAT WERE SHIPPED TODAY. THE DUO INSTALL WILL BE COMPLETE TODAY AND I DONT WANT REMOVE THE CHIP FROM THE DUO TO COMPLETE THE SLEEPER., CHIPS SHOULD ARRIVE BY FRIDAY ..
Im gonna label all the easy points on the front and the back of the CG PCB and you can decide where you want to wire, only 1 wire per color is needed so dont wire to the front and back of controller pcb. choose the best location for you to install each wire.
The reason for the colors with the black dots is i have 10 colors of kynar and to make install easier for me i will take a black sharpie and mark a line down the wires to make it easier to identify dupe colors.
VIKING 360 SLEEPER DIAGRAMS
PIN HEADER
IF YOUR PIN HEADER HAS 4 OR 6 PINS MAKE SURE YOU REMOVE THE ONES NOT NEEDED, I'VE MARKED THEM IN THE PIC BELOW.
NOTE: THE WIRE FOR THE A BUTTON CAN ONLY BE INSTALLED ON EITHER OF THE 2 GREEN POINTS ON THE BACK OF THE CHIP.
FRONT
BACK
NOTE: THE WIRE FOR THE A BUTTON CAN ONLY BE INSTALLED ON EITHER OF THE 2 GREEN POINTS ON THE BACK OF THE CHIP.
SLEEPER CG TOP
SLEEPER CG BOTTOM
(ONLY 7 EASY TO SOLDER POINTS ON THE BOTTOM)
DRILLING HOLE FOR USB PROGRAMER
THIS ONE IS HARD TO EXPLAIN CAUSE YOU WANT TO LINE IT UP CORRECTLY AND ITS KINDA HARD TO LINE UP AND MARK WITH THE PIN HEADER, SO I MADE ME A CARDBOARD CLONE THAT WORKED PERFECT. I TOOK A SMALL DRILL BIT AND DRILLED A HOLE IN THE CENTER OF EACH OF THE BLACK DOTS ON THE CARDBOARD, THEN LINED IT UP PROPERLY AND PUSHED A SMALL LATCH PIN THROUGH THE HOLE TO MARK THE DRILL SPOT. USED 5/32 FOR PILOT HOLE AND 17/64 FOR THE FINAL HOLE.